red stripe for bumper

[kumalaba]

how do you get the red stripe is it paint or tape also can you find the ford emblems for center caps? tks!

[wybnrml]

You can get 1/4" red pinstriping tape at most Auto Parts stores.

[gestiva]

Here is replacement FORD cap decals.

http://cgi.ebay.com/ebaymotors/FORD-SUV-METAL-COATED-CENTER-CAPS-STICKERS-DECALS-9cm-_W0QQcmdZViewItemQQitemZ120605442689QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

[wybnrml]

Here is replacement FORD cap decals.
http://cgi.ebay.com/ebaymotors/FORD-...Q5fAccessories

Those say they are 3.5" across.

[gestiva]

oops, Didnt read that.
Here are some that might work.

http://cgi.ebay.com/ebaymotors/FORD-SUV-METAL-COATED-CENTER-CAPS-STICKERS-DECALS-9cm-_W0QQcmdZViewItemQQitemZ120605442689QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

[kumalaba]

pinstripe

You can get 1/4" red pinstriping tape at most Auto Parts stores.

tks!

[kumalaba]

centercaps

Here is replacement FORD cap decals.
http://cgi.ebay.com/ebaymotors/FORD-...Q5fAccessories

tks!

[kumalaba]

caps

Those say they are 3.5" across.

tks i almost ordered them!!!!

[Aaronbrook37]

http://www.fordfestiva.com/forums/showpost.php?p=351867&postcount=9

I just did my bumpers both in paint and pinstripe this afternoon. Check out the link from my build thread to see the results! I was shocked at how much of a difference the painting and pinstriping did, but put together it's even better. Once I get my side moldings on, it'll look brilliant. The rear was tougher, but the front was more work. With the rear, you need a single piece, which can get difficult and tangled along the way. With the front, you should remove your license plate and holder, and you need three separate pieces to accommodate the turn signals.

[kumalaba]

tks

http://www.fordfestiva.com/forums/sh...67&postcount=9

I just did my bumpers both in paint and pinstripe this afternoon. Check out the link from my build thread to see the results! I was shocked at how much of a difference the painting and pinstriping did, but put together it's even better. Once I get my side moldings on, it'll look brilliant. The rear was tougher, but the front was more work. With the rear, you need a single piece, which can get difficult and tangled along the way. With the front, you should remove your license plate and holder, and you need three separate pieces to accommodate the turn signals.

i was just looking at your car 1 minute ago! great job & thanks for tips!

[Aaronbrook37]

A couple other pointers... when you fit it onto the bumper, pull on it to keep it tight and true, but not too tight. I have a few stretched spots... it has the strength of electrical tape, but with the adhesive strength of masking tape. I found scissors completely useless in trying to cut it, but blades work great! Good luck to you, they had a whole assortment of colours if you wanted to try anything other than red.

[kumalaba]

pinstripe

A couple other pointers... when you fit it onto the bumper, pull on it to keep it tight and true, but not too tight. I have a few stretched spots... it has the strength of electrical tape, but with the adhesive strength of masking tape. I found scissors completely useless in trying to cut it, but blades work great! Good luck to you, they had a whole assortment of colours if you wanted to try anything other than red.

thanks again for the tips i need red b/c sidemolding red oh yea do i have to take off the old stripe or just go on op of it? tks

[Aaronbrook37]

I haven't decided which one I'm going to do yet. If the old stuff is thicker/wider than the new, I'll try and get it off before re-taping it. If it gets stuck on, I'll paint over it with the bumper stuff hahaha!

[kumalaba]

stripe

I haven't decided which one I'm going to do yet. If the old stuff is thicker/wider than the new, I'll try and get it off before re-taping it. If it gets stuck on, I'll paint over it with the bumper stuff hahaha!

tks again!