Rare Parts

[freshtiva]

Here is how I installed mine

[bravekozak]

other yards

Most yards in the country have separate areas for similar cars.
Next time I'll take a few pics at some other yards I know.

I am disappointed that the under tray seat bottom is not interchangeable with the 1993 sleeved pull. I have to use the old bare wire and swap bottoms. I will have to take a hacksaw and cut the back seat mount off another 93.
Cut welds, drill out rivets, then reweld, rerivet.

http://bwbronze.com/festiva/tabbed_bottom.jpg

http://bwbronze.com/festiva/tabbed_bottom2.jpg

[SimonTuffGuy]

Wow... Your junkyard makes it nice. Just plop the cars all next to each other.

In my yard, you have to scour through countless rows until you stumble upon one. :-P

[bravekozak]

yesterday morning

I visited my http://bwbronze.com/festiva/favorite_spot.jpg in Michigan yesterday.

And found http://bwbronze.com/festiva/intact_air.jpg conditioning system.

and a chrome antenna.

I brought my tape measure this time. The cutout where I took the sunroof out, is exactly 7" from the front, and exactly 17" long X 31" wide.

http://bwbronze.com/festiva/big_hole.jpg

------------------------------------------

The rebuild kits for these carbs are $41 AU.
Good news, Australian dollars are cheaper than Canadian which is cheaper than American.
Bad news, you will need two of them.

I spoke to my machinist yesterday. He will use the original adapter as a template, since no hole is straight. I have yet to buy the aluminum. Probably this week.

[KrayZFrameRate]

i used to have a 323 for parts, i wish i would have known at the time i could have used the trunk release, i'll just have to remember that for the next time

I was at the junkyard yesterday and today and I saw oodles of mazda trunk/gas releases. How would you install that? All the festies I have seen have the locking cap. Also, where would the setup mount in the interior, I thought it was recessed by the driver seat into one of the support rails? Now I am going to have to go back to the yard tomorrow.....

[Damkid]

i used to have a 323 for parts, i wish i would have known at the time i could have used the trunk release, i'll just have to remember that for the next time

[geezerstiva]

i would also be interested in a twin carb w/ adapter. not trying to get ahead in line or anything, but that would be great to have!

[25Horseplay]

How about remote hatch and gas door poppers?!

I have a few sets of these, they come from 323's and Tracers.

[25Horseplay]

Brian, i called a twin carb first!!!! just gotta find the thread......

Haha Money talks and he said he has 2 set ups. I know it was llove at first site when I seen that set up.

[FestYboy]

Brian, i called a twin carb first!!!! just gotta find the thread......

[freshtiva]

I think the remote hatch and gas door popper is very practical. Is that out of a 323 David ?

[Amos]

How about remote hatch and gas door poppers?!

I want these and the antenna Give me a price.

[CHills]

How about remote hatch and gas door poppers?!

How much?

[David88]

How about remote hatch and gas door poppers?!

[25Horseplay]

When I said I had four, I mean four intakes X 2 carbs each = 8 carbs.

I will be selling two sets of them after I get the adapters machined.
I will keep one extra set for parts.
I haven't bought the 1" thick aluminum yet.

Only problem is, the air filter elements are $11 each and have to come from Australia.

Let me know. I would be interested in a set up!