What have you done to your Festiva today!?

[FeistyFesti]

Took pics of my side exit exhaust, pretty loud so I will install another Glass Pack behind the 25 inch long one to help reduce the loudness. It does pull a lot harder than before with seat of the pants dyno.

[kellen302]

you could try one of these http://www.streetperformance.com/par...-kv160105.html or a turndown for a more "finished" look also, Ill probably add a side dump with a e cutout for my swap, glad to see that the geometry works, nice job

[Charlie1717]

you could try one of these http://www.streetperformance.com/par...-kv160105.html or a turndown for a more "finished" look also, Ill probably add a side dump with a e cutout for my swap, glad to see that the geometry works, nice job

Like this

[FeistyFesti]

you could try one of these http://www.streetperformance.com/par...-kv160105.html or a turndown for a more "finished" look also, Ill probably add a side dump with a e cutout for my swap, glad to see that the geometry works, nice job

Thanks, that looks great, wonder if it'll cut down on the loudness.

[Zanzer]

Took a road trip to Raleigh to pick up a B6T. Hung out with Kartracer and Smedley...good times! :thumbright:

[M3NTAL]

Installed my FMS springs today!! and Camber bolts!!

[Basement_Modder]

Installed new battery terminals. Also picked up spark plugs, air filter, and oil filter. Going to change oil and filter tomorrow, and air filter/ spark plugs tonight hopefully.

[IdealSociety]

i looked at my car again for the first time in years and decided it needed to go back to being my main project car.

[gauge_half_inch]

Made caps for my spoiler, so now no hideous holes!

[neanderpaul]

i looked at my car again for the first time in years and decided it needed to go back to being my main project car.

Sounds promising! What's on the agenda?!

[IdealSociety]

Sounds promising! What's on the agenda?!

Im thinking of using my current BP car as a test-bed for several suspension redesigns ive been toying with for some years now but until my recent engineering classes wasnt sure how to pull it off. The primary design involves a direct bolt-in tubular front suspension that ties together all the major mounting points but would also allow (with some body trimming of course on the fender arches since they really arent properly arched) for a lower dual A-arm style hub suspension. it would push the hub surfaces pretty far out and would necessitate the use of wheels with a very high offset to push the wheels back under the fenderwells.

the rough sketches i put together in solidworks seem the principle idea should fit, however i need to research for a properly valved coil-over that will fit in the given area with the right amount of throw (which would need to be calculated after i test how much room is left for a redirectioning assembly that would change the struts force angle to a more outward one so it can all fit in place, all depending on strut/coil availability of course).

its hard to explain lol, hopefully i can use it as one of my semester projects.

the more simple stuff however is turbo upgrades, hopefully if my material costs end up close i might even have a prototype in a few months for a decent set of bolt-in rear disc adapters. if that small project ends up well ill be more than willing to openly post the CAD shematics and prints for others to use as well.

Trying to think of other things that ive been running through my mind. Most of them are suspension related, meant to replace the kinda crummy simplistic factory designs with something more akin to a proper race-car, without cutting into the unibody structure.

Years ago, i would have just cut in, now that im becoming an engineer i seem to be finding more fun in the challenge of working with previously designed restrictions instead.

getting close to 1am here now, as i really dig into things ill start picking back up my recording process and keep a good thread on the progress.

[Oren09]

Im thinking of using my current BP car as a test-bed for several suspension redesigns ive been toying with for some years now but until my recent engineering classes wasnt sure how to pull it off. The primary design involves a direct bolt-in tubular front suspension that ties together all the major mounting points but would also allow (with some body trimming of course on the fender arches since they really arent properly arched) for a lower dual A-arm style hub suspension. it would push the hub surfaces pretty far out and would necessitate the use of wheels with a very high offset to push the wheels back under the fenderwells.

the rough sketches i put together in solidworks seem the principle idea should fit, however i need to research for a properly valved coil-over that will fit in the given area with the right amount of throw (which would need to be calculated after i test how much room is left for a redirectioning assembly that would change the struts force angle to a more outward one so it can all fit in place, all depending on strut/coil availability of course).

its hard to explain lol, hopefully i can use it as one of my semester projects.

the more simple stuff however is turbo upgrades, hopefully if my material costs end up close i might even have a prototype in a few months for a decent set of bolt-in rear disc adapters. if that small project ends up well ill be more than willing to openly post the CAD shematics and prints for others to use as well.

Trying to think of other things that ive been running through my mind. Most of them are suspension related, meant to replace the kinda crummy simplistic factory designs with something more akin to a proper race-car, without cutting into the unibody structure.

Years ago, i would have just cut in, now that im becoming an engineer i seem to be finding more fun in the challenge of working with previously designed restrictions instead.

getting close to 1am here now, as i really dig into things ill start picking back up my recording process and keep a good thread on the progress.

That would be amazing.

[91_festy_Gl]

Spent 50 bucks in flat black rattlecan paint. can anyone say SPRAYBOMB? Nothing more ricer then a matte black festiva!

[htchbck]

Swapped in my Escort wiper gear into the motor I bought from Skim a while back... maybe this weekend I'll get around to cutting a hole in my hatch and installing it

[rollertoaster]

Installed my rear mud flaps. Finally got around to welding in a stud to mount my center belt to for my harness. Rigged up a holy crap strap for the passenger (they need it the way I drive). Removed some stickers that had been on the car since I got it. And installed a mounting plate for my in car camera setup.









I have a few more things to get done tomorrow. Need to go to the JY and pick up an aspire spare. Might make a new upper grill and install my hid driving lights behind some cutouts rather than sticking out the front like they are now. Also, I need to pre-register for the Delaware park rally-x on Sunday!


---
- Sent from my iPhone using Tapatalk