bare nipples and unplugged plugs

[Fecomatter]

So im trying to have my bp running by the end of the week, and I am not sure where some of these plugs go or what tubes need to go where. here is a picture of the plugs someone tell me what they are supposed to do. I see one going to a temperature sensor, but the temperature sensor that was connected via the old bp harness seems to be missing its own connector now.

http://s36.photobucket.com/user/Tommy_Tremains/media/84D75FA5-B153-4B31-9728-29485725A4FC_zps5wmltkdm.jpg.html?sort=3&o=4

These probably connect to something:

http://s36.photobucket.com/user/Tommy_Tremains/media/F55F4AB7-7483-4A1F-A69E-C01C0E107948_zps4bmsg3r0.jpg.html?sort=3&o=3

maybe to do with this?

http://s36.photobucket.com/user/Tommy_Tremains/media/26FEC515-4C32-4419-8A84-FDE0734EBCD0_zpsg5zdfcvd.jpg.html?sort=3&o=0

Then on the other side of the engine looks to be coming out of the intake manifold somewhere:

http://s36.photobucket.com/user/Tommy_Tremains/media/1DAD5A8B-F60B-49AD-BF8F-A2A16BD2931A_zpsqx8u1d6d.jpg.html?sort=3&o=1

[shadetree]

NOT WHAT I WAS EXPECTING ....DANG
1st picture of wires ....bottom is o2 sensor ...middle is coolant gauge sender ...top is fan control sender...
The coolant gauge sender is just behind the thermostat housing pointing towards the firewall , you will need to switch it with the festy stock sender for correct readings . The fan control sender is in the thermostat housing if you switched it with the stock one as well .
The hose on the left side of the engine connects to the booster hose . The two single hose pictures connect together , I just use a long piece and run it behind the firewall but don't forget the check valve .
And the picture of two hoses , they both plumb into the intake filter hose .on get a filter for the valve cover ànd block the iac off if you didn't wire it in .
I'm sure you didn't get all this so maybe ask again one ? At a time .

[Fecomatter]

hehehehe, gotcha.

so these to connect to the intake:

http://s36.photobucket.com/user/Tommy_Tremains/media/F55F4AB7-7483-4A1F-A69E-C01C0E107948_zps4bmsg3r0.jpg.html?sort=3&o=3

these two go together:

http://s36.photobucket.com/user/Tommy_Tremains/media/26FEC515-4C32-4419-8A84-FDE0734EBCD0_zpsg5zdfcvd.jpg.html?sort=3&o=0

http://s36.photobucket.com/user/Tommy_Tremains/media/1DAD5A8B-F60B-49AD-BF8F-A2A16BD2931A_zpsqx8u1d6d.jpg.html?sort=3&o=1

I know for a fact that I do not have the sensor that goes into the block, the "coolant gauge sender". Im only confused by the plugs still because the sensor on the thermostat housing has a little blade and looks like it goes into the black rectangle connector. Then plug with yellow inside looks like it connects to the o2 sensor.
you said the sensor in the thermostat housing is supposed to plug into the top, semi circlelooking plug, but on my festiva stock, it is a blade.

http://s36.photobucket.com/user/Tommy_Tremains/media/F5B3E52A-F0F9-45C4-B559-6BDA844FF270_zps4gajuxoe.jpg.html?o=6

Could you elaborate further? thank you.

[shadetree]

The flat blade is thermo housing sense and the round pin is the back off the head sensor . I ment in a line but anyway . The two coolant sensors will work but they will read higher on the gauge then the car is actually .

[Fecomatter]

RAD. thanks for the help, this will get all my plugs done tomorrow.