Announcement

Collapse
No announcement yet.

What have you done to your Festiva today!?

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Drove Green Car to work today. Was having a lot of trouble and I was suspecting it was low on fuel, even thought the needle on my new tach cluster was still showing between an 1/8 and a 1/4 tank. Put in five gallons and it ran great, so need to adjust the needle a bit since wifey will be driving it some . Found out one thing right away. It needs rotors. BAD! Like so bad I'm surprised I didn't actually see the warpage when I had the wheels off swapping them. I did look at the pads and they are brand new though. The second issue I found after I got to work. Its flinging oil all over the place, I think from the front crank seal but not 100% as it was still a little dark out. But its a running driving car that so far I have $350 for the purchase price, and $15 worth of gas in, so all in all, not bad. I did switch wheels and tires, but not because it needed it, I just wanted the alloys off of it for Babystiva. I'm happy with the way these 13s look on it now, but I do need to get rid of the 155/80s and go to something like a 155/70 or 165/70.

    Last edited by htchbck; 10-05-2011, 09:12 AM.
    No festiva for me ATM...

    Comment


    • added some evo rallyeye spotlights. Supercharger comes this week. Should be an interesting endeavor.
      Raising the bar for compact cars around the world.
      .:: 1997 Aspire ::. The Glowspire. Revived project
      .:: 1998 Aspire ::. The Glowspire red bean. Current Project



      My Ford Aspire DIY Wing Conversion
      Glow_Mouse's 97' Glowspire
      Glow_Mouse's 98' Glowspire
      Ford Aspire Forum Here!
      Order FordAspire.com Decals Range 1!
      Order FordAspire.com Decals Range 2!

      Comment


      • Put it back on all 4 wheels and loaded tools and parts in her to tow it home. It's been at my mom's all this time and i haven't had the time to get over there to work on it very often. I'm on the homestretch however
        1993 GL 5 speed

        It's a MazdaFordnKia thing, and you will understand!

        Comment


        • Found out my oil problem wasn't from a seal leak at lunchtime. It was blowing out of the dipstick tube. Major crankcase pressure! Pushed the dipstick up a couple inches and was blowing oil. Anyway, took off the pipe that goes from the intake tube to the valve cover and found that for some reason the bung on the intake tube was still shut solid. It was molded that way. So I hacked off an 1/8" from the end of it where it was sealed and hooked the pipe back up. No more blowing oil. Its burning a good bit of oil though, so may be the rings, but I'm hoping its just a bunch of oil that got up in the intake when things were out of whack, and maybe once that burns off it will quit. If not... B8 time lol.
          No festiva for me ATM...

          Comment


          • ^^^good call on catching it early let's hope. I read in the FMV thread about the oil intake issue and i wanted to say that pcv system has a serious issue address it asap.

            If you have the time you might want to unbolt the top of it all off and do a good cleaning....or not...almost as much work as a b8?
            1993 GL 5 speed

            It's a MazdaFordnKia thing, and you will understand!

            Comment


            • Slapped the sticker on this morning

              -Zack
              Blue '93 GL Auto: White 13" 5 Point Wheels, Full LED Conversion, and an 8" Sub

              Comment


              • Originally posted by getnpsi View Post
                If you have the time you might want to unbolt the top of it all off and do a good cleaning....or not...almost as much work as a b8?
                I'll be removing the entire intake (tube and manifold) probably this afternoon. Found a spare intake gasket in the back of the car when I got it, so I'm not out anything but a few minutes time. It did strike me as being odd that the intake tube was completely blocked off on the small drivers side pipe nipple though. Tube to the VC was in place like it should be though, just the inside of that pipe nipple was still closed. And as for a B8... hmmm, don't know if I have that much time laying around to install one of those I bet I can do it in two weekends
                No festiva for me ATM...

                Comment


                • Replaced valve cover gasket on the BP and degreased as much oil off the engine as possible and washed it all off while engine was cold. Installed a Bulldog security remote start for the coming cold mornings. Soldered all wires even under the dash using super thin solder for quick melting. Took me forever to figure out why it would only run for 30 seconds, then reprogrammed to start "tachless" and now she stays at the programmed 15 minutes setting. Damn wife couldn't remember where she left the camera til I was done with all wiring. I can do a write up if people are interested, while memory is still fresh.


                  Changed the oil and filter with 3 quarts 10w 30 Havoline petro oil and a Fram 6X Extraguard filter and one quart of Lucas oil stabilizer.
                  Semper Fi til I die!

                  1993 Fescort GT 1.8 BP automatic Kia Rio front struts and cut springs Cut Front Festiva springs with Monroe Aspire struts in rear


                  Comment


                  • New front tires arrived from TireRack.com in lightning fast delivery. Can't wait to get payed and paint the front rims & get them mounted to complete my fresh set of shoes for the Festy
                    Send An Invite If Ya Want




                    1991 Ford Festiva GL- Auto

                    Comment


                    • Hauled a b8 home in it for a swap.
                      Ford Fester

                      Comment


                      • Pic
                        Ford Fester

                        Comment


                        • Originally posted by Ford Fester View Post
                          Pic
                          NIce choice that is a really fun swap!!

                          heres what i did today in 40 mins its not as hard as everyone thinks !!!

                          93 L B6T DD http://www.fordfestiva.com/forums/sh...ad.php?t=37751
                          RIP_90 LuX http://www.fordfestiva.com/forums/sh...ad.php?t=32249
                          RIP 88 LX / B8-MEhttp://www.fordfestiva.com/forums/sh...ad.php?t=26398

                          RJ

                          Comment


                          • I rallied mine in my buddy's field. We're working on setting up a practice course. Almost ripped off the airdamn, but I don't care. I want to make a new one anyway, and it was totally worth it!


                            Sent from my iPhone using Tapatalk

                            Comment


                            • I parked it in my garage for the winter before the white stuff fall from the sky

                              BPT, G5M-R, BP26 Exintake swap + Fidanza cam gear, NSRT4 FMIC + 2.5" piping, HKS SSQV BOV, Exedy clutch, 3" downpipe + 2" all the way back, Aspire brake swap, KYB GR-2 & FMS coil spring , FMS EURO body kit + Carbon fiber hood, Falcon RTX 15X6½ + Toyo proxes T1R 195/45R15

                              Comment


                              • i got a second gen b6 head done for one of my projects today. That's about it, work seems to get in the way of all my progress.
                                91 Festiva GL "Scrat"
                                82 Honda Goldwing GL1100i
                                85 BMW 535is "Brunhild"

                                Comment

                                Working...
                                X