What have you done to your Festiva today!?

[link5186]

Yesterday I received and installed my b6 ecm. Using my b3 vaf with a slight adjustment until I find another one

Sent from the bathroom via crapatalk

[zoom zoom]

Theres so much awesomeness in that trucktiva, words cannot describe it.

Got new NGK Plugs, can't wait to install, im hoping it'll kill the slight 1/2" vibration in my vacuum gauge occasionally!

[ENEMY_]

Took it for a photoshoot. I posted a few pics in the gallery forum

[IdealSociety]

bought more turbo parts. also bought rear brakes to get it back on the road this weekend.

pics to come if i can get her running

[freshtiva]

Got some different wheels mounted on Frankenstiva. Still missing an "Eagle Alloy" center cap. I see some on ebay for $25 each which is more than I paid for the wheels. :shock:

[ericsmith32]

Ouch that's a bit steep! How does it ride with those rims? Speaking of tires one of the Festiva's has a flat.. that's a first. Typically it's the Escape with flats.

[Nerd Racing]

Oh i'll have it fixed up over the weekend, i'm just not looking forward to pulling the motor again

can't you just drop the trans down and slide it off? or is this way easier?

got the festiva inspected today and picked up a pair of outer tie rod ends...

[Joe Dirt]

My engine kit came today, ordered a new flywheel and a clutch, need to get the motor set out

[freshtiva]

Ouch that's a bit steep! How does it ride with those rims?

Rides fine, I drove it hard down the hwy to test it out. I actually have better clearance at the rear strut perch now. Someone must have had a bad tire on one of the rims. They tire guy removed four ounces of weight from one rim and only had to add 3/4 of an ounce back to get it balanced.

[91_festy_Gl]

http://www.fordfestiva.com/forums/showthread.php?p=449635&highlight=resurected#post449635

[Damkid]

can't you just drop the trans down and slide it off? or is this way easier?

I think the crank pulley would hit the frame before the tranny dropped low enough to get off the engine



Last night i pulled the motor/trans and found a hole in the tranny case.... the diff pin rotated and sheared the roll pin and worked its way out of the diff to carve the hole in the case...... stupid phantom grips..... anyway, today i got the next hybrid tranny ready, then bolted it to the motor and got them back in the festiva... another hour of work and it'll be back up and running

I have pics of the damage but photobucket's not co-operating, once i get pics loaded i'll post them

[walth]

wow, just one thing after another for you eh chris?

I just bought rotors and pads for my front aspire swap. gonna rebuild the calipers tonight and get the knuckles and struts ready for tomorrow morning and have it swapped up and ready for the meet.

[ericsmith32]

Rides fine, I drove it hard down the hwy to test it out. I actually have better clearance at the rear strut perch now. Someone must have had a bad tire on one of the rims. They tire guy removed four ounces of weight from one rim and only had to add 3/4 of an ounce back to get it balanced.

Yeah that tire was bad.. still had good tread the only reason I kept it. Need to put it on the back next time.

[Damkid]

wow, just one thing after another for you eh chris?

Yup lol although i always had a worry about the phantom grip causing this problem.... luckily i was able to drive it home and this didn't happen on my way to FM5

So needless to say i have a regular open diff in my car now until i can afford an Mfactory diff, and hopefully no more break downs for a while

[jamesmc]

Re-did all my ghetto wiring, this time using solder and heatshrink. Makes me feel comfortable that my car won't blow up or catch fire. :confused2: Fixed my left brake light, spoiler brake light, and dome light. Speedometer cable snapped, so I replaced that as well. Also, ordered my cold air intake. Loving this BP.