What have you done to your Festiva today!?

[sactnato]

Replaced the Ford grill emblem with the new one I got from Green Sales Company.

[bravekozak]

Today I tried to figure out why my headlights weren't working. No success. Power goes through my combination switch, but does not make it to the headlamps. They used to work! If I take off my driver's fender and find a mouse ate through my 89 headlamp wires, it will be mouse warfare time. I already have glue traps set up on top of all the blocks holding the car up in the air.
I changed the brown glovebox latch on the gray glovebox with a gray one.
I also changed distributors. I encountered a serious problem. the ignition module terminals are slightly smaller on the 1986 B6 distributor.

[bravekozak]

I discovered today that the extra M4 X 0.7 stainless steel screws that I bought for my fuel tank sender, also fit both external holes on the distributor housing. I will install it tomorrow morning and report back.
Also Justin Sparr from ACP Composites emailed me regarding a cheap, rigid, lightweight cards for my doors. We shall see.

[TorqueEffect]

Picked up 8 quarts of Valvoline racing synthetic 10w30 for less than $7 total. One of the AutoZones on my route were clearing it out for a dollar a quart, so combined with my discount it came to like $6.50.

[TorqueEffect]

Trying to figure out how to attach the shifter stabilizer bar to the transmission when the stud is missing, and the boss is damaged.

[1990new]

Forgot to wish you a merry Christmas, tried to pm you again and your inbox is full. Lol

And a Merry one to you too. I have now cleaned out my inbox.

[bravekozak]

Just got back from the finger lakes. The Bosch B6 distributor cap that I picked up, fits just fine. I have four or five used B3 distributors that would be happy to donate a couple of wires for the sake of science. I will not need the wire to the barometric pressure sensor, since the B6 ignition module does not support that type of signal for advance.

hopeful, a pair of compound action Knipex mini cutters will make removing the old hog rings a piece of cake. Be sure to presoak the covers to get most of the dirt out before you throw it in the washing machine. The water will be black as coal.

[Festivahopeful]

cleaning seats

I got my hog ring pliers yesterday, so have been busy dismantling seats. The back is done, now on to the fronts.
100_1223.jpg
When I started on the front seat I found a surprise
100_1225.jpg
Two total so far, they look like they could sting a feller
100_1227.jpg
Pictures from when I changed valve cover gasket last week.
100_1206.jpg
100_1205.jpg

[TorqueEffect]

If it's just new outer tie rod ends you need, PM me and I'll give you a deal you can't refuse.

Forgot to wish you a merry Christmas, tried to pm you again and your inbox is full. Lol

[1990new]

Car is back on the car and running. Now to attend to the stabilizer bar. Need to get me a stud, and jbweld it to the damaged boss. Extremely sloppy shifting with that stabilizer bar just tied up to the steering rack. So as long as I am gentle, I can get into all the gears just fine. After that it will need at least some cheap tie-rod ends since my brother who is a professional mechanic said they are pretty bad, then take it to this place that I saw that does $30 alignments.

If it's just new outer tie rod ends you need, PM me and I'll give you a deal you can't refuse.

[TorqueEffect]

Car is back on the car and running. Now to attend to the stabilizer bar. Need to get me a stud, and jbweld it to the damaged boss. Extremely sloppy shifting with that stabilizer bar just tied up to the steering rack. So as long as I am gentle, I can get into all the gears just fine. After that it will need at least some cheap tie-rod ends since my brother who is a professional mechanic said they are pretty bad, then take it to this place that I saw that does $30 alignments.

[Festivahopeful]

I have a spec clutch in my g series if the stickers are to be believed and an old for sale ad. Either way, I love it. I don't beat it up, but it engages nicely and really grabs. When I first got the car the clutch was very stiff and temperamental, but the more I drive it the better it gets; I think it was pretty new and not broke in.

[TorqueEffect]

Old transmission is off, and the replacement bolted onto the engine, and all both back in and bolted to the car. Now to put everything back together. Taking so much time, because we are working with limited light, no air tools, in a cold garage, and only doing things a few hours at a time before I have to pack back up and head home.

Axles came out without too much of a fight, my balljoints didn't want to pop out of the knuckles, so we just popped the tie-rods out instead for the clearance for the axles.

[TorqueEffect]

Last night we got most of the stuff connecting to the engine and transmission unhooked, and moved out of the way. Just forgot to bring a jack. DOH!! Going back after work today to finish the job.

Hopefully I will be driving my Festy home tonight with a fully functional 5-speed.

[J Eric]

Today, I replaced my + battery terminal and adjusted my throttle cable.